Info

SsTC7S00F tqfp100 ssTC7S00F TK11228AM so16 Pindix2 bar63-05w 50v 3ghz sot323 MosFet P FDC Mad4 rom2 f721979 c10 tqfo176 IC, SRAM IC, flash mem. IC, EEPROM IC, 1xnand 2input cmos Cafe d wfa157dt100 IC, 1xnand 2input cmos IC, regulator Chaps charger control Ccont2h dct3 bb asic lbga8x8 IC, regulator MC33765 IC, 2xsyn2.5g 510mhz tssopLMX2330L IC, PLL MB15S70 Odyssey v3 mfg-379 qsop24 Transistor x 2 Tif wfd165at32t tqfp32 Shark5 pa 11a_3 824-849mhz Snapper4 pa 9j 1850-1910mhz Transistor x 2 IC,...

Rx If Agc

RX IF Compensation 1900 MHz CDMA Tx IF AGC Tuning Max Power, TX_LIM_ADJ tuning (1900) 42 LNA GAIN SWITCH RX IF AGC (1900MHz) Rx If Compensation Factory The Software Flash File Procedure to Flash a Advanced The Dealer PRL (Preferred Roaming Subscriber Data (NAM) Phone Book (Short Code Memory) SID NID Programming (Preferred Forbidden SID NID) . . 52 Factory Reset Default NAM Parameter A-Key Programming Calling Card Warranty Information The View Menu RF Parameters (used only for Special Service...

Chaps

Audio Gain), provides system clock squaring, utilizes PLL for CDMA clock generation from system clock, and interfaces to the RF section and to MAD4. The CCONT ASIC provides linear regulated power to most of the phone. It has a multiplexed A D converter for temperature sensor digitization, battery voltage, charger voltage, current consumption, and battery type detection. An external 32 kHz oscillator circuit is connected to CCONT, which is used for sleep clock generation. It also has a watchdog...

Vctcxo

Vctcxo From Pwm

T3 62 ms, PURX delay generated by CCONT After PWR-key has been pushed, CCONT gives PURX reset to MAD4 and turns on VR1, VBB and VR6 regulators (if battery voltage has exceeded 3.0 V). VR1 supplies VCTCXO, VBB supplies MAD, and VR6 supplies digital parts of CAFE. After the initial delay, t2, VCTCXO starts to give a proper 19.2MHz clock to CAFE, which further divides it to 9.83MHz for MAD4. CAFE will output the 9.83MHz clock only after the PURX reset has been removed. After delay, t3, CCONT...

Ignition Sense IGNS

The ignition sense feature prevents your car kit from draining the car battery by executing an auto power off in 20 seconds after the ignition key has been turned off. The blue wire of the power cable is used for the ignition sense feature. The use of ignition sense is recommended to prevent accidental draining of the car's battery. The wire is connected via a 1 A fuse to a 12 24 volt potential that is controlled by the ignition key. Do not connect it directly to the high voltage sections of...

Technical Summary

The HFU-2 has connections to car battery, car ignition sense, car radio muting, antenna motor control, data-card, handset HSU-1, external speaker and microphone. The unit has a System-connector that provides an interface to the Mobile holder MCC-1 via the external cable. The unit consists of a rapid charger, HF-microphone- and speaker amplifiers, interface to handset, - datacard and -phone, voltage regulators and control circuit (microprocessor). The HFU-2 is always connected to the car...

Flash Prommer FPSS Sales Pack

The Flash Prommer FPS-4S is used to update the main software of the phone. Updating is done by first loading the new MCU software from the PC to the flash prommer, and then loading the new SW from the prommer to the phone. When updating more than one phone in succession, the MCU software only needs to be loaded to the prommer once. - D9 - D9 Cable AXS-4 0730090 - Installation software for FPS-4 8400041

Chaps Battery

Nokia 6185

With 2-wire charging the charger provides constant output current, and the charging is controlled by PWMOUT signal from CCONT to CHAPS. PWMOUT signal frequency is selected to be 1 Hz, and the charging switch in CHAPS is pulsed on and off at this frequency. The final charging current to the battery is controlled by adjusting the PWMOUT signal pulse width. Both the PWMOUT frequency selection and pulse width control are made by the MCU which writes these values to CCONT. The 2-wire charger is part...

Win Tesla Core Software Installation

The WinTesla core software is delivered on a 3.5 diskette and is protected with a protection key PKD-1 or PKD-1D which must be attached to the parallel port LPT1 when the WinTesla service software is being used. Keep the original diskette safe to enable upgrading of the program. To install the WinTesla software package, proceed as follows NOTE For instructions on installing the service module see Phone Specific Service Module Installation 1. Insert the WinTesla Application diskette into your...

Warnings

ENSURE THAT THE VEHICLE'S BATTERY IS DISCONNECTED BEFORE YOU START THE INSTALLATION PROCEDURE, AND THAT IT REMAINS DISCONNECTED DURING THE PROCEDURE. 2. DO NOT SMOKE OR USE OPEN FLAMES WHEN WORKING NEAR THE VEHICLE'S FUEL SYSTEM. 3. ENSURE THAT THE VEHICLE'S ELECTRICAL CABLES, HYDRAULIC LINES, FUEL LINES, AND SAFETY EQUIPMENT ARE NOT DAMAGED DURING INSTALLATION. 4. ENSURE THAT NORMAL CONTROL AND OPERATION OF THE VEHICLE IS NOT IMPAIRED BY THE INSTALLATION, PARTICULARLY THE BRAKES AND...